1 Litre Relax Pool Leak Sealer - Box of 6
Hazards Identification
Classification of the substance or mixture
- Classification under CLP: STOT SE 3: H335; Eye Dam. 1: H318; Skin Irrit. 2: H315
Signal Words - Danger
Hazard Statements
- H315: Causes skin irritation
- H318: Causes serious eye damage
- H335: May cause respiratory irritation
Precautionary Statements
- P261: Avoid breathing dust/fumes/gas/mist/vapours/spray
- P280: Wear protective gloves/protective clothing/eye protection/face protection
- P302+350: IF ON SKIN: Gently wash with plenty of soap and water
- P304+340: IF INHALED: Remove person to fresh air and keep comfortable for breathing
- P305+351+338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue ri
- P337+313: If eye irritation persists: Get medical
Supplemental Hazard Information (EU)
- NONE
Other Hazards
- This product is not identified as a PBT/vPvB substance
First Aid Measures
- Contact with skin
- Remove all contaminated clothes and footwear immediately unless stuck to skin
- Wash immediately with plenty of soap and water
- Contact with eyes
- Check for and remove any contact lenses
- Open eyes wide apart. Rinse opened eye with plenty of water for at least 15 minutes
- Get medical attention
- Ingestion
- Wash out mouth with water
- Do not induce vomiting
- f conscious, give half a litre of water to drink immediately
- Consult a doctor
- Inhalation
- Remove casualty from exposure ensuring one's own safety whilst doing so
Most important symptoms and effects, both acute and delayed
- Contact with eyes
- There may be pain and redness
- The eyes may water profusely
- There may be severe pain
- The vision may become blurred
- May cause permanent damage
- Contact with skin
- There may be irritation and redness at the site of contact
- Ingestion
- There may be soreness and redness of the mouth and throat
- Nausea and stomach pain may occur
- Inhalation
- There may be irritation of the throat with a feeling of tightness in the chest
Indication of immediate medical attention and special treatment needed
- Immediate effects can be expected after short-term exposure
| SKU | RCH102 |
|---|---|
| Re-stock date | In stock |
| Manufacturer | Plastica |
| Hazardous | No |
| EAN | 5055672117476 |
| Single Item Ean | 5055672142058 |
| Complete Box ASIN | B0DM273MTW |
| Single Item ASIN | B0DM2BB2LN |
| Discount Group | T5 |
| Lead Time (Days) | 0 |
| Pallet Qty | 60 Boxes |
Leak Sealer
DIRECTIONS FOR USE
Important: Bypass filter when using this product. Leak Sealer is not recommended
to repair torn vinyl swimming pool liners, for this you must use a vinyl repair kit. Leak Sealer
is designed to seal minor leaks (where the water level drops less than 2.5cm per day in a
60,000 litre pool). Larger defects will require proper plumbing and maintenance repairs.
- Turn pool pump off. Remove any automatic pool cleaner from the pool.
- SET THE FILTER ON BY-PASS OR RE-CIRCULATE SETTING. If neither of these
settings are available then remove the filter grids or cartridges from the filter prior to
commencing treatment. NOTE: Fine fountain jets will block when leak sealer is applied. If
these jets cannot be removed then do not use this product.
- Leak Sealer should be added to the pool at the rate of 1 litre per 60,000 litres of pool
water. There are two methods of application depending on the location of the leak.
- a) LEAK IN POOL WALLS OR FLOOR – Add the leak sealer directly into the pool water.
Where it is possible to locate the area of the leak then add the product in this area.
Otherwise distribute the product evenly around the pool.
- b) LEAK IN PIPEWORK – Add the correct dose of leak sealer directly into the skimmer.
Leak sealer is a heavy product that will collect at the deep end. To ensure maximum
effectiveness circulate the product as follows. Set up a pool vacuum hose (with a vacuum
head attached) as for normal cleaning. Place the vacuum head at the deepest point
in the pool. Ensure the hose is free of air. This method ensures maximum circulation
through the pipework. If unsure of the location of the leak use method b.
- Wait 30 minutes and then turn the pump on. Leave the pump running for a minimum of
8 hours.
- Mark the water level and check after 24 hours.
- A second application may be required in larger pools.
- Return the filter setting to normal once the leak sealer has taken effect and resume
normal filtration. Swimming may be resumed 24 hours after addition of product.
